Pilot Login

Login with Password

Test Report

Advance Epsilon 8 25 | 5556P66349

Equipment
Advance Epsilon 8 25 | 5556P66349
Production Date: Apr 2016
Service
Passed
Rating
Used, good conditions
Date
14. May 2026
Next Service
May 2028 or after 150 flight hours or 150 Flights
Service Center
myCheck48.de

Checker: Wolfgang Hogen
Notice
Your glider has undergone a service. Before flying, it is essential that you test-inflate and thoroughly check it.

Gallery

Porosity Test

Gauge HELLO

1. Measurement 205 [s]

2. Measurement 186 [s]

Rating Passed

Fabric Tear Resistance

Bettsometertest Passed

Visual Inspection: Canopy

Rods Passed

Loops Passed

Topsail Passed

Cell walls Passed

Lower sail Passed

Leading edge Passed

Rating Passed

Visual Inspection: Lines

Main lines Passed

Bei Leine CI links, CIII rechts, AI rechts wurde eine Beschädigung festgestellt. Für diese Leinen wurde ein Ersatz angefertigt und in den Schirm eingebaut.

Brake lines Passed

Beide Brems- Stammleinen wurden erneuert,

Gallery lines Passed

Rating Passed

Visual Inspection: Risers

Risers Passed

Line locks Passed

Speed system Passed

Rating Passed

Linen Tear Strength

Left / 1A1 Minimum strength: 110 daN / Measured strength: 133 daN - Passed

Rating Passed

Trimm

Mainlines
ST 3 2 1 1 2 3 ST
DL SL SL SL
A
SL SL SL SL
SL SL SL
B
SL SL SL
DL DL SL
C
SL DL DL
The left brake line was extendet by 23mm. The right brake line was extendet by 21mm.
SL
DL
AS
AS+
AS++
Description of Paraglider Trimming

Chord Line and Angle of Attack in Paragliders
  • Chord Line: The imaginary straight line running from the leading edge (front) to the trailing edge (back) of the paraglider profile. It represents the basic shape of the wing.
  • Angle of Attack: The angle between the chord line of the paraglider and the oncoming airflow. It is crucial for determining how much lift the wing generates.

Comparison: Optimally Trimmed vs. Out-of-Trim Paraglider
  1. Optimally Trimmed Paraglider
    • Chord Line: The chord line is relatively straight and continuous from the leading to the trailing edge. The profile is evenly tensioned with no significant deformations.
    • Angle of Attack: The angle of attack is relatively constant across the span and optimal for the current flight condition (e.g., straight flight). Air flows smoothly over and under the profile, generating efficient lift with minimal drag. The wing flies stably, glides well, and is easy to control.
    Imagine a smooth, even curvature of the wing, with airflow gliding cleanly over the top and bottom surfaces.
  2. Out-of-Trim Paraglider
    A paraglider is "out of trim" when the line lengths are no longer correct, usually due to aging, uneven loading, or improper repairs. This leads to profile deformation.
    • Chord Line: The chord line is no longer straight or even. Depending on the type of trim error (e.g., A-lines too long, B- or C-lines too short, or vice versa), the profile may be deformed in certain areas.
      • Example: Brake lines (or C-lines) too short relative to B/A: The trailing edge is pulled down more than intended. The chord line bends downward at the rear, increasing the camber.
      • Example: A-lines too long (or B/C-lines too short relative to A): The leading edge is more "open" or pushed upward, while the rest of the profile may be flatter. The chord line at the front forms a different angle to the flight direction.
    • Angle of Attack: The angle of attack is uneven and often suboptimal across the span.
      • With a downward-pulled trailing edge, the local angle of attack increases, causing more drag and less efficiency. The wing may respond sluggishly, glide poorly, and be more prone to stalls.
      • With a deformed leading edge, the angle of attack may be too low, increasing the risk of front collapses.
    Imagine the wing having "bumps" or "dents" in some places, disturbing the smooth airflow and making the wing less efficient and potentially unsafe.

Summary:
A diagram would show that, in an optimally trimmed paraglider, the chord line forms a clean, efficient shape and the angle of attack is consistent everywhere. In an out-of-trim paraglider, the chord line bends or curves unevenly, resulting in a suboptimal and varying angle of attack, which negatively affects flight characteristics.

Linen Length: Left

A Linen
Left / A Linen
Ref. Act. Diff.
7009 7011 2
6946 6948 2
6882 6883 1
6829 6830 1
6736 6729 -7
6629 6624 -5
6538 6541 3
6523 6528 5
Average 0
Tolerance (-10,10)
ST Linen
Left / ST Linen
Ref. Act. Diff.
6260 6260 0
6242 6245 3
6029 6027 -2
6071 6064 -7
6139 6136 -3
6207 6203 -4
Average -2
Tolerance (-15,10)
B Linen
Left / B Linen
Ref. Act. Diff.
6904 6905 1
6845 6844 -1
6785 6781 -4
6740 6735 -5
6674 6668 -6
6578 6572 -6
6493 6496 3
6478 6483 5
Average -2
Tolerance (-10,10)
C Linen
Left / C Linen
Ref. Act. Diff.
7022 7023 1
6962 6959 -3
6886 6881 -5
6832 6828 -4
6733 6730 -3
6628 6627 -1
6528 6536 8
6511 6518 7
Average 0
Tolerance (-10,10)
D Linen
Left / D Linen
Ref. Act. Diff.
7151 7152 1
7088 7084 -4
7005 7002 -3
6939 6934 -5
Average -3
Tolerance (-10,10)
BR Linen
Left / BR Linen
Ref. Act. Diff.
7409 7394 -15
7075 7077 2
7002 7005 3
6784 6797 13
6634 6642 8
6538 6553 15
6535 6548 13
6425 6444 19
6303 6318 15
6243 6262 19
6173 6189 16
Average 10
Tolerance (-10,50)

Linen Length: Right

A Linen
Right / A Linen
Ref. Act. Diff.
7009 7006 -3
6946 6952 6
6882 6880 -2
6829 6830 1
6736 6726 -10
6629 6622 -7
6538 6540 2
6523 6524 1
Average -2
Tolerance (-10,10)
ST Linen
Right / ST Linen
Ref. Act. Diff.
6260 6265 5
6242 6248 6
6029 6034 5
6071 6072 1
6139 6139 0
6207 6208 1
Average 3
Tolerance (-15,10)
B Linen
Right / B Linen
Ref. Act. Diff.
6904 6903 -1
6845 6845 0
6785 6786 1
6740 6737 -3
6674 6670 -4
6578 6571 -7
6493 6493 0
6478 6478 0
Average -2
Tolerance (-10,10)
C Linen
Right / C Linen
Ref. Act. Diff.
7022 7017 -5
6962 6959 -3
6886 6885 -1
6832 6833 1
6733 6725 -8
6628 6621 -7
6528 6528 0
6511 6515 4
Average -2
Tolerance (-10,10)
D Linen
Right / D Linen
Ref. Act. Diff.
7151 7144 -7
7088 7084 -4
7005 7003 -2
6939 6935 -4
Average -4
Tolerance (-10,10)
BR Linen
Right / BR Linen
Ref. Act. Diff.
7409 7399 -10
7075 7072 -3
7002 7008 6
6784 6803 19
6634 6646 12
6538 6554 16
6535 6553 18
6425 6442 17
6303 6313 10
6243 6253 10
6173 6186 13
Average 10
Tolerance (-10,50)