Pilot Login

Login with Password

Test Report

Advance Alpha 7 28 | 104320

Equipment
Advance Alpha 7 28 | 104320
Production Date: June 2024
Service
Passed
Rating
Used, very good conditions
Date
21. July 2026
Next Service
July 2028 or after 150 flight hours
Service Center
myCheck48.de

Checker: Wolfgang Hogen
Notice
Your glider has undergone a service. Before flying, it is essential that you test-inflate and thoroughly check it.

Gallery

Porosity Test

Gauge HELLO

1. Measurement 1260 [s]

Rating Passed

Fabric Tear Resistance

Bettsometertest Passed

Visual Inspection: Canopy

Rods Passed

Loops Passed

Topsail Passed

Cell walls Passed

Lower sail Passed

Leading edge Passed

Rating Passed

Visual Inspection: Lines

Main lines Passed

Brake lines Passed

Gallery lines Passed

Bei Leine a 3 rechts wurde eine Beschädigung festgestellt. Für diese Leine wurde ein Ersatz angefertigt und in den Schirm eingebaut.

Rating Passed

Visual Inspection: Risers

Risers Passed

Line locks Passed

Speed system Passed

Rating Passed

Linen Tear Strength

Right / 1A1 Minimum strength: 166 daN / Measured strength: 237 daN - Passed

Right / 1B1 Minimum strength: 126 daN / Measured strength: 168 daN - Passed

Rating Passed

Trimm

Mainlines
ST 3 2 1 1 2 3 ST
SL SL SL SL
A
SL SL SL SL
SL SL SL
B
SL SL SL
SL SL SL
C
SL SL SL
The left brake line was extendet by 21mm. The right brake line was extendet by 20mm.
SL
DL
AS
AS+
AS++
Description of Paraglider Trimming

Chord Line and Angle of Attack in Paragliders
  • Chord Line: The imaginary straight line running from the leading edge (front) to the trailing edge (back) of the paraglider profile. It represents the basic shape of the wing.
  • Angle of Attack: The angle between the chord line of the paraglider and the oncoming airflow. It is crucial for determining how much lift the wing generates.

Comparison: Optimally Trimmed vs. Out-of-Trim Paraglider
  1. Optimally Trimmed Paraglider
    • Chord Line: The chord line is relatively straight and continuous from the leading to the trailing edge. The profile is evenly tensioned with no significant deformations.
    • Angle of Attack: The angle of attack is relatively constant across the span and optimal for the current flight condition (e.g., straight flight). Air flows smoothly over and under the profile, generating efficient lift with minimal drag. The wing flies stably, glides well, and is easy to control.
    Imagine a smooth, even curvature of the wing, with airflow gliding cleanly over the top and bottom surfaces.
  2. Out-of-Trim Paraglider
    A paraglider is "out of trim" when the line lengths are no longer correct, usually due to aging, uneven loading, or improper repairs. This leads to profile deformation.
    • Chord Line: The chord line is no longer straight or even. Depending on the type of trim error (e.g., A-lines too long, B- or C-lines too short, or vice versa), the profile may be deformed in certain areas.
      • Example: Brake lines (or C-lines) too short relative to B/A: The trailing edge is pulled down more than intended. The chord line bends downward at the rear, increasing the camber.
      • Example: A-lines too long (or B/C-lines too short relative to A): The leading edge is more "open" or pushed upward, while the rest of the profile may be flatter. The chord line at the front forms a different angle to the flight direction.
    • Angle of Attack: The angle of attack is uneven and often suboptimal across the span.
      • With a downward-pulled trailing edge, the local angle of attack increases, causing more drag and less efficiency. The wing may respond sluggishly, glide poorly, and be more prone to stalls.
      • With a deformed leading edge, the angle of attack may be too low, increasing the risk of front collapses.
    Imagine the wing having "bumps" or "dents" in some places, disturbing the smooth airflow and making the wing less efficient and potentially unsafe.

Summary:
A diagram would show that, in an optimally trimmed paraglider, the chord line forms a clean, efficient shape and the angle of attack is consistent everywhere. In an out-of-trim paraglider, the chord line bends or curves unevenly, resulting in a suboptimal and varying angle of attack, which negatively affects flight characteristics.

Linen Length: Left

A Linen
Left / A Linen
Ref. Act. Diff.
7443 7439 -4
7397 7398 1
7346 7345 -1
7325 7325 0
7231 7233 2
7113 7112 -1
7050 7046 -4
Average -1
Tolerance (-10,10)
ST Linen
Left / ST Linen
Ref. Act. Diff.
6712 6710 -2
6728 6724 -4
6481 6480 -1
6549 6548 -1
Average -2
Tolerance (-15,10)
B Linen
Left / B Linen
Ref. Act. Diff.
7318 7321 3
7277 7280 3
7234 7235 1
7219 7219 0
7160 7159 -1
7060 7060 0
7010 7007 -3
Average 0
Tolerance (-10,10)
C Linen
Left / C Linen
Ref. Act. Diff.
7415 7419 4
7383 7386 3
7375 7378 3
7331 7333 2
7310 7314 4
7343 7346 3
7226 7229 3
7107 7109 2
7034 7039 5
Average 3
Tolerance (-10,10)
D Linen
Left / D Linen
Ref. Act. Diff.
7517 7522 5
7484 7484 0
7475 7473 -2
7427 7430 3
7405 7406 1
7427 7428 1
7304 7307 3
7174 7176 2
7084 7086 2
Average 2
Tolerance (-10,10)
BR Linen
Left / BR Linen
Ref. Act. Diff.
7821 7827 6
7579 7588 9
7400 7410 10
7323 7335 12
7180 7195 15
7061 7074 13
6993 7006 13
6988 7001 13
6835 6839 4
6781 6785 4
6684 6694 10
6583 6595 12
Average 10
Tolerance (-10,50)

Linen Length: Right

A Linen
Right / A Linen
Ref. Act. Diff.
7443 7438 -5
7397 7399 2
7346 7344 -2
7325 7328 3
7231 7228 -3
7113 7109 -4
7050 7044 -6
Average -2
Tolerance (-10,10)
ST Linen
Right / ST Linen
Ref. Act. Diff.
6712 6707 -5
6728 6724 -4
6481 6482 1
6549 6550 1
Average -2
Tolerance (-15,10)
B Linen
Right / B Linen
Ref. Act. Diff.
7318 7314 -4
7277 7278 1
7234 7235 1
7219 7219 0
7160 7159 -1
7060 7058 -2
7010 7005 -5
Average -1
Tolerance (-10,10)
C Linen
Right / C Linen
Ref. Act. Diff.
7415 7417 2
7383 7384 1
7375 7378 3
7331 7332 1
7310 7310 0
7343 7346 3
7226 7225 -1
7107 7105 -2
7034 7032 -2
Average 1
Tolerance (-10,10)
D Linen
Right / D Linen
Ref. Act. Diff.
7517 7519 2
7484 7483 -1
7475 7476 1
7427 7432 5
7405 7402 -3
7427 7426 -1
7304 7305 1
7174 7174 0
7084 7086 2
Average 1
Tolerance (-10,10)
BR Linen
Right / BR Linen
Ref. Act. Diff.
7821 7822 1
7579 7586 7
7400 7404 4
7323 7330 7
7180 7193 13
7061 7070 9
6993 7003 10
6988 6995 7
6835 6840 5
6781 6788 7
6684 6695 11
6583 6595 12
Average 8
Tolerance (-10,50)